MotoHouston.com MotoHouston.com
Register Members List Member Map Media Calendar Garage Forum Home Mark Forums Read

Go Back   MotoHouston.com > General Discussion > General Discussion (Moto Related)
Forgot info?

Welcome to MotoHouston.com! You are currently viewing our forums as a guest which gives you limited access to the community. By joining our free community you will have access to great discounts from our sponsors, the ability to post topics, communicate privately with other members, respond to polls, upload content, free email, classifieds, and access many other special features. Registration is fast, simple and absolutely free, join our community!

Register Today!

If you have any problems with the registration process or your account login, please contact us.


Like us on Facebook! Regular shirt GIVEAWAYS and more

Advertisement

Reply
Share This Thread: 
Subscribe to this Thread Thread Tools
Old 02-12-2009, 05:06 PM   #1
ekfraz
Senior Member
 
ekfraz's Avatar
 
Join Date: Oct 2008
Location: NW HOUSTON/COPPERFIELD
Feedback Rating: (0)
Posts: 485

Experience: 10+ years

Bike(s):
2013 Can Am Spyder RT
2014 Yamaha Bolt








Cool Frame Sliders (question)

I ordered frame sliders for my 2006 YZF 600 and I am not too sure where they go, it did not come with directions, they are the no drill or cut sliders.
ekfraz is offline   Reply With Quote
Similar Topics
Thread Thread Starter Forum Replies Last Post
Frame sliders scooter09 General Discussion (Moto Related) 19 12-12-2012 01:50 PM
Frame sliders question Mr.D General Discussion (Moto Related) 19 02-25-2011 09:27 AM
Frame Sliders? Eddy.T General Discussion (Moto Related) 5 12-03-2010 10:47 AM
Frame Sliders NgaWhat General Discussion (Moto Related) 10 05-19-2010 04:57 PM
frame sliders optionet General Discussion (Moto Related) 10 04-12-2007 02:35 PM
Advertisement
Old 02-12-2009, 05:55 PM   #2
ileono918
On hiatus
 
Join Date: Aug 2008
Feedback Rating: (4)
Posts: 6,047

Experience: 1-3 months
Trackdays: 1











What brand? It is really easy to install them. Should not take more than 5 minutes.
ileono918 is offline   Reply With Quote
Old 02-12-2009, 06:02 PM   #3
ekfraz
Senior Member
 
ekfraz's Avatar
 
Join Date: Oct 2008
Location: NW HOUSTON/COPPERFIELD
Feedback Rating: (0)
Posts: 485

Experience: 10+ years

Bike(s):
2013 Can Am Spyder RT
2014 Yamaha Bolt








I am not sure of the brand but they are inscribed with YZF, I really don't see a spot to screw them in, it has two bolts and two washers with the sliders.
ekfraz is offline   Reply With Quote
Old 02-12-2009, 06:09 PM   #4
TexasYZF600R
Ya.Ma.Ha.
 
Join Date: Jan 2009
Location: Dickinson, Texas
Feedback Rating: (2)
Posts: 236

Experience: 4 years
Trackdays: 1

Bike(s):
2oo5 Yamaha R6
2oo4 Yamaha YZF600R (sold)



Member Garage


http://www.yzf600r.com<<<join this forum as well

You will need an 8mm hex wrench to loosen the upper engine mount bolt.

1. Start on the right side of the bike (do not loosen both sides at once) by removing the upper engine mount bolt, which is visible through the fairing cowl. Do not loosen the frame pinch bolts.
2. These sliders are side specific, so for the right side, install the slider with the aluminum spacer extending(about .5Ē) from the base of the slider. Pay close attention to this because a slider installed on the wrong side will cause damage to the bolt hole threads.
3. If using a torque wrench, tighten bolt to 35 lb/ft.
4. Make sure the right side is tight before starting on the left side.
5. For the left side, use the same procedure, except, of course, using the slider with the flat base. Remember, donít loosen the frame pinch bolts.
Mounting points for each side are basically the same- use the upper bolt of the two engine mount bolts.
__________________
the end as we know it

Last edited by TexasYZF600R; 02-12-2009 at 06:13 PM.
TexasYZF600R is offline   Reply With Quote
Old 02-12-2009, 06:26 PM   #5
Azylum
The Chosen One
 
Azylum's Avatar
 
Join Date: Jan 2007
Location: Ellington
Feedback Rating: (23)
Posts: 39,629

Experience: 8 years
Trackdays: 2











they go where your engine mount bolts go. just make sure to only take out one bolt at a time.
__________________
motohoustonlogo
Bringing back the old school.
Azylum is offline   Reply With Quote
Old 02-12-2009, 06:50 PM   #6
ekfraz
Senior Member
 
ekfraz's Avatar
 
Join Date: Oct 2008
Location: NW HOUSTON/COPPERFIELD
Feedback Rating: (0)
Posts: 485

Experience: 10+ years

Bike(s):
2013 Can Am Spyder RT
2014 Yamaha Bolt








Thanks, I will give it a try.
ekfraz is offline   Reply With Quote
Reply


Thread Tools

Advertisement


All times are GMT -5. The time now is 07:28 PM.


MotoHouston.com is not responsible for the content posted by users.
Privacy Policy