MotoHouston.com MotoHouston.com
Register Members List Member Map Media Calendar Garage Forum Home Mark Forums Read

Go Back   MotoHouston.com > Technical > How To's and Q & A's
Forgot info?

Welcome to MotoHouston.com! You are currently viewing our forums as a guest which gives you limited access to the community. By joining our free community you will have access to great discounts from our sponsors, the ability to post topics, communicate privately with other members, respond to polls, upload content, free email, classifieds, and access many other special features. Registration is fast, simple and absolutely free, join our community!

Register Today!

If you have any problems with the registration process or your account login, please contact us.


FREE MH Decals by MAIL!

Advertisement

Reply
Share This Thread: 
Subscribe to this Thread Thread Tools
Old 03-25-2012, 03:04 PM   #1
cbrmonkey
aka Joe
 
cbrmonkey's Avatar
 
Join Date: Feb 2012
Feedback Rating: (0)
Posts: 341

Experience: 2 years

Bike(s):
07' CBR600RR




Member Garage





barend weights

......so I'm trying to replace barends, after the old weight is off there is threaded piece that i can't get out of the handle ... I have a 01 cbr 600...how do I get that part out, if anyone knows ,thanks in advance.
cbrmonkey is offline   Reply With Quote
Similar Topics
Thread Thread Starter Forum Replies Last Post
flywheel weights. 95badbird Dirtbikes, Mini's, ATV's..... 7 12-03-2013 06:25 PM
Heavy Weights gsxrjai Off Topic 6 09-10-2009 05:40 PM
Wheel weights MC16 How To's and Q & A's 17 11-12-2008 03:34 PM
anyone here lift weights?? speedracer2536 Off Topic 8 07-29-2008 12:25 AM
CRG v Napoleon barend mirrors. logan5 General Discussion (Moto Related) 1 05-05-2008 01:54 PM
Advertisement
Old 03-25-2012, 03:36 PM   #2
bc6140
Senior Member
 
bc6140's Avatar
 
Join Date: Nov 2009
Location: S.E.
Feedback Rating: (1)
Posts: 718

Experience: 3 years

Bike(s):
2008 gsxr 600




Member Garage





Put the bar end back in a little bit, try workin it up/down or back and forth.. it should come loose
bc6140 is offline   Reply With Quote
Old 03-25-2012, 03:45 PM   #3
cbrmonkey
aka Joe
 
cbrmonkey's Avatar
 
Join Date: Feb 2012
Feedback Rating: (0)
Posts: 341

Experience: 2 years

Bike(s):
07' CBR600RR




Member Garage





Ok Thx I'll try that
cbrmonkey is offline   Reply With Quote
Old 03-25-2012, 06:39 PM   #4
gots2no
Steve
 
gots2no's Avatar
 
Join Date: Feb 2012
Location: Pearland
Feedback Rating: (0)
Posts: 936

Experience: 10+ years
Trackdays: 10+

Bike(s):
'94 Kawasaki ZX6
'78 Yamaha XS750E (sold)
'82 Yamaha Seca 750 (sold)
'82 Yamaha XT200 (sold)

Member Garage





On mine, the bar ends were held with the red Loctite - the tough stuff. If I recall the bar end had the stud machined (or pressed) onto it, so it sounds like it may have sheared off. You might try a screw extractor, but my experience with those is not good. I generally break them off in the seized fastener, and then I have a seized faster with a hardened piece of steel embedded in it. Good luck.
gots2no is offline   Reply With Quote
Old 03-25-2012, 09:29 PM   #5
Patrick
Motorcycles Unlimited
 
Join Date: Jun 2005
Location: Houston
Feedback Rating: (2)
Posts: 16,367

Experience: 10+ years
Trackdays: 10+

Bike(s):
'14 Speed Triple R, '82 CB900F, '13 Streetglide






On the Hondas there are little tabs holding the weights in.
Roll the grip up and you'll see two 1/8" holes close to the end of the bar.
The tabs snap into that.
Use a punch and knock the tabs down out of the holes and then you can pull the weight out.
On the throttle side you need to remove the throttle housing & tube to get to it.
__________________
Call or PM for the BEST PRICES in Houston for PARTS and ACCESSORIES.
MAKE SURE TO MENTION YOU'RE ON MH TO GET THE BEST PRICE!

NEED GEAR? We have a great selection in stock but if we need to order it we GUARANTEE FIT!
Where Houston riders go to have their bikes worked on, done right the first time!


muad

1964 FM 1960 West
Houston, TX 77090
Hours: Tues.-Fri. 9:30-6:00 Sat. 9-5:30
www.motorcycles-unlimited.com
http://www.facebook.com/motorcyclesunlimited
e-mail: patrick@motorcycles-unlimited.com

Last edited by Patrick; 03-25-2012 at 10:33 PM.
Patrick is offline   Reply With Quote
Old 03-25-2012, 10:13 PM   #6
cbrmonkey
aka Joe
 
cbrmonkey's Avatar
 
Join Date: Feb 2012
Feedback Rating: (0)
Posts: 341

Experience: 2 years

Bike(s):
07' CBR600RR




Member Garage





Thx I will try again tomorrow
cbrmonkey is offline   Reply With Quote
Reply


Thread Tools

Advertisement


All times are GMT -5. The time now is 09:40 PM.


MotoHouston.com is not responsible for the content posted by users.
Privacy Policy