Welcome back to us :/ Our hosts data center was down for the entire day.
MotoHouston.com MotoHouston.com
Register Members List Member Map Media Calendar Garage Forum Home Mark Forums Read

Go Back   MotoHouston.com > General Discussion > General Discussion (Moto Related)
Forgot info?

Welcome to MotoHouston.com! You are currently viewing our forums as a guest which gives you limited access to the community. By joining our free community you will have access to great discounts from our sponsors, the ability to post topics, communicate privately with other members, respond to polls, upload content, free email, classifieds, and access many other special features. Registration is fast, simple and absolutely free, join our community!

Register Today!

If you have any problems with the registration process or your account login, please contact us.


Like us on Facebook! Regular shirt GIVEAWAYS and more

Advertisement

Reply
Share This Thread: 
Subscribe to this Thread Thread Tools
Old 05-07-2011, 05:46 PM   #1
ST675
01101000 01101001
 
ST675's Avatar
 
Join Date: Jun 2008
Location: Cypress
Feedback Rating: (3)
Posts: 1,378

Experience: 10+ years

Bike(s):
lots of bikes from 80cc to 1200cc
Current : ZX11
KX80







Need to replace the rear wheel bearings

This past wed I started to hear a popping sound at lower speeds so I put the bike up and drove the truck ( gas prices ). at first I thought the chain needed cleaning / lube because it been weeks from the last time I did it. I re-adjusted the chain and was moving the rear tire and all sounded well.

But then I tightened the axle bolt and the popping came back...

It looks like the rear wheel bearings are shot. Specificially the disk brake side ( it does not move by hand ). The sprocket side moves ok and the sprocket carrier moves great.

I think this may be one of those fixes I have a shop do just because i'm irritated at the bike and was hoping for a few weekends of no bike work. but has anyone changed the rear bearings on an 05 Bandit 1200 wheel? Did you have to use a bearing puller? I was looking at the spacer between the bearings and it does not give much room to get an extention in and hit it after you heat up the hub... How much are the pullers?

LOL maybe I will take to pedal bike to work for this week just so I dont have $100 fill ups on the truck....
__________________
That may be your first bike....but its not your last....

Last edited by ST675; 05-07-2011 at 05:49 PM.
ST675 is offline   Reply With Quote
Similar Topics
Thread Thread Starter Forum Replies Last Post
Adjusting Wheel Bearings Track_Graphics General Discussion (Moto Related) 7 09-06-2013 04:43 PM
Need wheel spacers and bearings jakeg How To's and Q & A's 0 07-04-2013 10:54 AM
May have tapped the wheel bearings in too far... zombiejesus How To's and Q & A's 1 06-22-2010 06:31 PM
RC51 rear wheel bearings dangelo_texas How To's and Q & A's 3 08-22-2009 04:08 PM
Remove wheel bearings Los How To's and Q & A's 13 02-22-2007 04:05 PM
Advertisement
Old 05-08-2011, 03:26 PM   #2
Patrick
Motorcycles Unlimited
 
Join Date: Jun 2005
Location: Houston
Feedback Rating: (2)
Posts: 16,368

Experience: 10+ years
Trackdays: 10+

Bike(s):
'14 Speed Triple R, '82 CB900F, '13 Streetglide






You can drive them out from the opposite side one at a time. Make sure to replace all 3; the 2 wheel bearings and the one in the hub. I either have the bearings in stock or can get them in one day if you need them.
__________________
Call or PM for the BEST PRICES in Houston for PARTS and ACCESSORIES.
MAKE SURE TO MENTION YOU'RE ON MH TO GET THE BEST PRICE!

NEED GEAR? We have a great selection in stock but if we need to order it we GUARANTEE FIT!
Where Houston riders go to have their bikes worked on, done right the first time!


muad

1964 FM 1960 West
Houston, TX 77090
Hours: Tues.-Fri. 9:30-6:00 Sat. 9-5:30
www.motorcycles-unlimited.com
http://www.facebook.com/motorcyclesunlimited
e-mail: patrick@motorcycles-unlimited.com

Last edited by Patrick; 05-08-2011 at 04:36 PM.
Patrick is offline   Reply With Quote
Old 05-08-2011, 04:28 PM   #3
Sabatech
Jesse Does it ALL
 
Sabatech's Avatar
 
Join Date: Nov 2008
Location: sw houston
Feedback Rating: (10)
Posts: 427

Experience: 10+ years

Bike(s):
Hayabusa
2001 GSXR 1000
2004 GSXR 1000
RC 51
426 Supermoto






Send a message via MSN to Sabatech Send a message via Skype™ to Sabatech
PnP can do it for 65 if you bring the bearings... just fyi
Sabatech is offline   Reply With Quote
Old 05-08-2011, 04:45 PM   #4
Squanto84
Ruh Roh..
 
Squanto84's Avatar
 
Join Date: Jul 2006
Location: Pearland
Feedback Rating: (7)
Posts: 2,384

Experience: 10+ years
Trackdays: 10+






Member Garage





Holy , 65 dollars!?
__________________
Roadracing a dirtbike..? Now that's just stupid! -Dad
Squanto84 is offline   Reply With Quote
Old 05-08-2011, 10:03 PM   #5
derekvercher
Senior Member
 
derekvercher's Avatar
 
Join Date: Mar 2011
Location: china tx
Feedback Rating: (0)
Posts: 188

Experience: 10+ years

Bike(s):
1998 honda cbr 600 f3
2003 honda cr250r
yamaha pw50







It's easy. Do it yourself
derekvercher is offline   Reply With Quote
Reply


Thread Tools

Advertisement


All times are GMT -5. The time now is 06:46 AM.


MotoHouston.com is not responsible for the content posted by users.
Privacy Policy